Kramer-electronics VS-44HDCP Manuale Utente

KRAMER ELECT RONIC S LTD. USER MANUAL MODEL: VS-44HDCP 4x4 DVI Matrix Switcher P/N: 2900-300210 Rev 2

VS-44HDCP - Installing in a Rack 7 7 4 Installing in a Rack This section provides instructions for rack mounting the unit.

8 VS-44HDCP - Connecting the VS-44HDCP 5 Connecting the VS-44HDCP Always switch off the power to each device before connecting it to your VS-44HD

VS-44HDCP - Connecting the VS-44HDCP 9 9 Figure 3: Connecting to the VS-44HDCP Rear Panel

10 VS-44HDCP - Operating the VS-44HDCP 4x4 DVI Matrix Switcher 6 Operating the VS-44HDCP 4x4 DVI Matrix Switcher This section describes how to: 

VS-44HDCP - Operating the VS-44HDCP 4x4 DVI Matrix Switcher 11 11 6.3 Storing and Recalling a Setup You can use the STO and RCL buttons to store up

12 VS-44HDCP - Operating the VS-44HDCP 4x4 DVI Matrix Switcher 6.4 Locking and Unlocking the Front Panel To prevent unintended tampering with the u

VS-44HDCP - Operating the VS-44HDCP 4x4 DVI Matrix Switcher 13 13 6.5.2 Acquiring an EDID from Several Sets of Inputs and Outputs To acquire the ED

14 VS-44HDCP - Operating the VS-44HDCP 4x4 DVI Matrix Switcher 6.5.3 Acquiring the Default EDID To store the default EDID on a selected input (for

VS-44HDCP - Controlling the VS-44HDCP 15 15 7 Controlling the VS-44HDCP You can control the VS-44HDCP via the  RS-232 serial commands transmitted

16 VS-44HDCP - Controlling the VS-44HDCP 7.2.1 Connecting the Ethernet Port directly to a PC You can connect the Ethernet port of the VS-44HDCP di

VS-44HDCP - Controlling the VS-44HDCP 17 17 4. Highlight either Internet Protocol Version 6 (TCP/IPv6) or Internet Protocol Version 4 (TCP/IPv4) de

18 VS-44HDCP - Controlling the VS-44HDCP Figure 7: Internet Protocol Version 6 Properties Window 6. Select Use the following IP Address for static

VS-44HDCP - Controlling the VS-44HDCP 19 19 Figure 8: Internet Protocol Properties Window 7. Click OK. 8. Click Close. 7.2.2 Connecting the Ethe

20 VS-44HDCP - Controlling the VS-44HDCP 7.3 Using the IR Transmitter You can use the RC IR3 IR transmitter to control the machine via the built-i

VS-44HDCP - Firmware Upgrade 21 21 8 Firmware Upgrade For instructions on upgrading the firmware see “Upgrading the VS-44HDCP Firmware Using the ST

22 VS-44HDCP - Technical Specifications 9 Technical Specifications INPUTS: 4 DVI connectors OUTPUTS: 4 DVI connectors BANDWIDTH: Up to 6.75Gbps dat

VS-44HDCP - Default Communication Parameters 23 23 10 Default Communication Parameters RS-232 Protocol 2000 (Default) Protocol 3000 Baud Rate: 96

24 VS-44HDCP - Default EDID 11 Default EDID Monitor Model name... VS-44HDCP Manufacturer... KRM Plug and Play ID...

VS-44HDCP - Default EDID 25 25 YCbCr 4:2:2... Supported Native formats... 1 Detailed timing #1... 720x480p at 60Hz (4:3

26 VS-44HDCP - Protocol 3000 12 Protocol 3000 By default, the VS-44HDCP is set to Protocol 2000 (see Section 13) but is also compatible with Krame

VS-44HDCP – Contents i Contents 1 Introduction 1 2 Getting Started 2 2.1 Achieving the Best Performance 2 2.2 Safety Instructions 2 2.3 Re

VS-44HDCP - Protocol 3000 27 27 12.1.2 Device Message Format Start Address (optional) Body delimiter ~ device_id@ Message CR LF 12.1.2.1 Device Lon

28 VS-44HDCP - Protocol 3000 Message closing character CR – For host messages; carriage return (ASCII 13) CRLF – For device messages; carriage retu

VS-44HDCP - Protocol 3000 29 29 12.2 Kramer Protocol 3000 Commands Command Short Form Description Permission # Protocol handshaking End User BUIL

30 VS-44HDCP - Kramer Protocol 2000 13 Kramer Protocol 2000 The Kramer Protocol 2000 RS-232/RS-485 communication uses four bytes of information as

VS-44HDCP - Kramer Protocol 2000 31 31 Instruction Codes for Protocol 2000 Instruction Definition for Specific Instruction Notes # Description Input

32 VS-44HDCP - Kramer Protocol 2000 would be HEX codes 4B 80 81 85 NOTE 8 - The reply is as in TYPE 3 above, except that here the OUTPUT is assi

For the latest information on our products and a list of Kramer distributors, visit our Web site where updates to this user manual may b

VS-44HDCP - Introduction 1 1 1 Introduction Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world of unique, cre

2 VS-44HDCP - Getting Started 2 Getting Started We recommend that you:  Unpack the equipment carefully and save the original box and packaging ma

VS-44HDCP - Getting Started 3 3 2.3 Recycling Kramer Products The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC aims to red

4 VS-44HDCP - Overview 3 Overview The VS-44HDCP is a high quality 4x4 DVI matrix switcher. It reclocks and equalizes the signals and can route any

VS-44HDCP – Overview 5 3.1 Defining the VS-44HDCP 4x4 DVI Matrix Switcher This section defines the VS-44HDCP. Figure 1: VS-44HDCP 4x4 DVI Matrix

Figure 2: VS-44HDCP 4x4 DVI Matrix Switcher Rear Panel # Feature Function 12 IN DVI Connectors Connect to the DVI/HDMI (over DVI-D connector) sourc