Kramer-electronics TP-410 Manuale Utente

KRAMER ELECTRONICS LTD. USER MANUAL MODEL: TP-410 UXGA-Audio-RS-232 Line Transmitter / DA P/N: 2900-000733 Rev 3

# Feature Function 21 RS-485 (G,B,A) Connect to the RS-485 controller. Pins B (-) and A (+) are for RS-485; connect pin G to the cable shield (if r

8 TP-410 - Installing in a Rack 4 Installing in a Rack This section provides instructions for rack mounting the unit.

TP-410 - Connecting the TP-410 9 9 5 Connecting the TP-410 This section describes how to connect: • The TP-410 (see Section 5.1• Several TP-410

10 TP-410 - Connecting the TP-410 6. Connect the 10 TP OUTPUT STP/UTP connectors to up to 10 TP receivers (for example, the TP-126 or additional T

TP-410 - Connecting the TP-410 11 11 5.2 Connecting to the TP-410 via an RS-232 Connection You can operate the destination devices (for example, d

12 TP-410 - Connecting the TP-410  If required, connect the GND pin on the RS-485 port of the PC to the G (ground) pin on the rear panel of the T

TP-410 - Connecting the TP-410 13 13 Figure 5: Local Area Connection Properties Window 6. Select Use the following IP Address, and fill in the de

14 TP-410 - Connecting the TP-410 Use your PC initially to configure the Ethernet settings using K-UPLOAD software. When configuration is complete,

TP-410 - Configuration and Distribution of Control Data 15 15 6 Configuration and Distribution of Control Data The TP-410 distributes VGA, audio

16 TP-410 - Configuration and Distribution of Control Data Figure 8: Local Control via RS-232 6.1.2 Connecting a PC via the Ethernet In this exam

TP-410 - Configuration and Distribution of Control Data 17 17 6.1.3 The Remote Mode In the remote mode, the PC is connected to the RS-232 port on

18 TP-410 - Configuration and Distribution of Control Data Figure 11: Connecting Multiple TP-410 Units via RS-485

TP-410 - The SETUP DIP-switches 19 19 7 The SETUP DIP-switches The DIP-switches on the TP-410 set the machine number of the unit. Moving a DIP-

20 TP-410 - The SETUP DIP-switches 7.1.1 ETH Configuration To configure the Ethernet parameters, set DIP-switches 1 to 4 to ON (ON-ON-ON-ON), tur

TP-410 - The SETUP DIP-switches 21 21 7.3 Setting the RS-485 Bus Termination The DIP-switch sets the RS-485 bus termination. Only the first and la

22 TP-410 - Wiring the CAT 5 LINE IN / LINE OUT RJ-45 Connectors 8 Wiring the CAT 5 LINE IN / LINE OUT RJ-45 Connectors This section defines the C

TP-410 - Acquiring the EDID 23 23 9 Acquiring the EDID The TP-410 can acquire the EDID information from a display connected to the UXGA IN 15-pin

24 TP-410 - Flash Memory Upgrade 10 Flash Memory Upgrade You can upgrade the TP-410 via the Kramer K-UPLOAD software. Before running K-UPLOAD, set

TP-410 - Technical Specifications 25 25 11 Technical Specifications INPUTS: 1 UXGA on a 15-pin HD connector 1 unbalanced stereo audio on a 3.5mm

26 TP-410 - Technical Specifications 11.1 Communication Parameters EDID EDID data is passed to the local Input RS-232 Protocol 2000 Baud Rate: Up

TP-410 – Contents i Contents 1 Introduction 1 2 Getting Started 2 2.1 Achieving the Best Performance 2 3 Overview 3 3.1 Shielded Twisted

TP-410 - Default EDID 27 27 12 Default EDID The factory default EDID is listed below. Monitor Model name... TP-410 Manufacturer..

28 TP-410 - Kramer Communication Protocol 2000 13 Kramer Communication Protocol 2000 The RS-232/RS-485 Protocol 2000 uses four bytes of informatio

TP-410 - Kramer Communication Protocol 2000 29 29 INSTRUCTION DEFINITION FOR SPECIFIC INSTRUCTION NOTES # DESCRIPTION INPUT OUTPUT 2C CONTROLS

        

TP-410 – Introduction 1 1 Introduction Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world of unique, creati

2 TP-410 - Getting Started 2 Getting Started We recommend that you: • Unpack the equipment carefully and save the original box and packaging mate

TP-410 – Overview 3 3 Overview The TP-410 UXGA-Audio-RS-232 Line Transmitter / DA is a high performance, 10-channel VGA/UXGA, audio and data to

4 TP-410 - Overview In addition, the TP-410: • Can automatically differentiate between RS-232/RS-485 commands that control the unit itself and co

Figure 1: TP-410 UXGA-Audio-RS-232 Line Transmitter / DA Front Panel # Feature Function 1 POWER LED Lights when the unit receives power 2 AUDIO

TP-410 – Overview 6 Figure 2: TP-410 UXGA-Audio-RS-232 Line Transmitter / DA Rear Panel # Feature Function 8 EDID STATUS LED Lights during no